AC/DC Clamp. Features a range of 30A and 300A AC & 45A and 450A DC.
AC/DC Clamp. Features a range of 30A and 300A AC & 45A and 450A DC.
The Fluke i310s Current Probe is based on Hall Effect technology for use in measurement of both DC and AC current.
The Fluke i310s Current Probe may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement.
Using advanced Hall Effect technology, the Clamp can accurately measure currents up to 450 A peak over the frequency range of dc to 20 kHz. These features make it a powerful tool for use in inverters, switch mode power supplies, industrial controllers, automotive diagnostics, and other applications requiring current measurements and/or waveform analysis.
| Electrical Characteristics | |||||
| Current Ranges |
|
||||
| 30 A and 300 A ACRMS or ±45 A and 450 A DC | |||||
| ACRMS or DC |
|
||||
| ±45 A and 450 A | |||||
| Inrush Current |
|
||||
| 600A ACRMS MAX | |||||
| Output Sensitivity |
|
||||
| 10 mV/A (30 A) | |||||
| 1 mV/A (300 A) | |||||
| Accuracy (at +25°C) |
|
||||
| (30A range) | ±1% of reading ±50 mA | ||||
| (300A range) | ±1% of reading ±300 mA | ||||
| Bandwidth to meet accuracy specification |
|
||||
| 1 kHz | |||||
| Phase Shift below 1 kHz |
|
||||
| < 2 degrees</td> | |||||
| Resolution |
|
||||
| ±50 mA (30 A) | |||||
| ±100 mA (300 A) | |||||
| Load Impedance |
|
||||
| > 10 k Ohms and ≤100 pF | |||||
| Conductor Position Sensitivity |
|
||||
| ±1.5% relative to centre reading | |||||
| Frequency Range |
|
||||
| (small signal) | DC to 20 kHz (- 3 dB) | ||||
| Temperature Coefficient |
|
||||
| ±0.1% of reading /°C | |||||
| Power Supply |
|
||||
| 9 V Alkaline, MN1604/PP3 | |||||
| Battery Life |
|
||||
| 30 Hours, low battery indicator | |||||
| Working Voltage (see Safety Standards section) |
|
||||
| 300 V ACRMS or DC | |||||
| General Characteristics | |||||
| Maximum Conductor Size |
|
||||
| 19 mm diameter | |||||
| Output Connection |
|
||||
| Safety BNC connector | |||||
| Supplied with safety 4mm adaptor | |||||
| Output Zero |
|
||||
| Manual adjust via thumbwheel | |||||
| Cable Length |
|
||||
| 2 metres | |||||
| Operating Temperature Range |
|
||||
| -10 to +50°C | |||||
| Storage Temperature Range (with battery removed) |
|
||||
| -20 to +85°C | |||||
| Operating Humidity |
|
||||
| 15% to 85% (non-condensing) | |||||
| Weight |
|
||||
| 250 g | |||||
| Safety Standards | |||||
| BS EN 61010-1 |
|
||||
| 2001 | |||||
| BS EN 61010-2-032 |
|
||||
| 2002 | |||||
| BS EN 61010-031 |
|
||||
| 2002 | |||||
| 300 VRMS, Category III, Pollution Degree 2 | |||||
| Note |
|
||||
| Use of the probe on un-insulated conductors is limited to 300 V ACRMS or DC and frequencies below 1 kHz. | |||||
| EMC Standards |
|
||||
| BS EN 61236 | 1998 +A1, A2, & A3 | ||||
Click on a category to view a selection of compatible accessories with the Fluke i310s Current Probe.
| Electrical Characteristics | |||||
| Current Ranges |
|
||||
| 30 A and 300 A ACRMS or ±45 A and 450 A DC | |||||
| ACRMS or DC |
|
||||
| ±45 A and 450 A | |||||
| Inrush Current |
|
||||
| 600A ACRMS MAX | |||||
| Output Sensitivity |
|
||||
| 10 mV/A (30 A) | |||||
| 1 mV/A (300 A) | |||||
| Accuracy (at +25°C) |
|
||||
| (30A range) | ±1% of reading ±50 mA | ||||
| (300A range) | ±1% of reading ±300 mA | ||||
| Bandwidth to meet accuracy specification |
|
||||
| 1 kHz | |||||
| Phase Shift below 1 kHz |
|
||||
| < 2 degrees</td> | |||||
| Resolution |
|
||||
| ±50 mA (30 A) | |||||
| ±100 mA (300 A) | |||||
| Load Impedance |
|
||||
| > 10 k Ohms and ≤100 pF | |||||
| Conductor Position Sensitivity |
|
||||
| ±1.5% relative to centre reading | |||||
| Frequency Range |
|
||||
| (small signal) | DC to 20 kHz (- 3 dB) | ||||
| Temperature Coefficient |
|
||||
| ±0.1% of reading /°C | |||||
| Power Supply |
|
||||
| 9 V Alkaline, MN1604/PP3 | |||||
| Battery Life |
|
||||
| 30 Hours, low battery indicator | |||||
| Working Voltage (see Safety Standards section) |
|
||||
| 300 V ACRMS or DC | |||||
| General Characteristics | |||||
| Maximum Conductor Size |
|
||||
| 19 mm diameter | |||||
| Output Connection |
|
||||
| Safety BNC connector | |||||
| Supplied with safety 4mm adaptor | |||||
| Output Zero |
|
||||
| Manual adjust via thumbwheel | |||||
| Cable Length |
|
||||
| 2 metres | |||||
| Operating Temperature Range |
|
||||
| -10 to +50°C | |||||
| Storage Temperature Range (with battery removed) |
|
||||
| -20 to +85°C | |||||
| Operating Humidity |
|
||||
| 15% to 85% (non-condensing) | |||||
| Weight |
|
||||
| 250 g | |||||
| Safety Standards | |||||
| BS EN 61010-1 |
|
||||
| 2001 | |||||
| BS EN 61010-2-032 |
|
||||
| 2002 | |||||
| BS EN 61010-031 |
|
||||
| 2002 | |||||
| 300 VRMS, Category III, Pollution Degree 2 | |||||
| Note |
|
||||
| Use of the probe on un-insulated conductors is limited to 300 V ACRMS or DC and frequencies below 1 kHz. | |||||
| EMC Standards |
|
||||
| BS EN 61236 | 1998 +A1, A2, & A3 | ||||
Click on a category to view a selection of compatible accessories with the Fluke i310s Current Probe.
